Tools You Need to Install a New Bath Tub
Tools You Need to Install a New Bath Tub
Blog Article
The content in the next paragraphs pertaining to How to Install a Bathtub is incredibly remarkable. Read it for your own benefit and decide what you think of it.
Installing a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently accessible, the task can move easily; if you need to open a wall surface to remove the old bathtub and place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the work and fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have already acquired a new tub and also don't require to transform the plan of your previous water system pipelines.
Your tools and also material checklist need to consist of the following:
Planning for the Installment
Firstly, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted access that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipes have been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, put the bathtub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the tub until the level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water as well as check all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub as well as additionally inspect the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub ought to wait till the bathtub has actually been made use of at least once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washers remain in area in between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap adapters. The previous kind should be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in complications with dampness and possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can split relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that piece was essential. Enjoyed our blog posting? Please share it. Help someone else locate it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Pricing
Report this page